What are the symptoms of a bad water pump?

The most common symptoms of a failing water pump include: coolant leaking from the weep hole at the bottom of the pump (a small designed drain that indicates seal failure), engine overheating or temperature gauge reading higher than normal, a squeaking, grinding, or rumbling noise from the pump bearing area that changes with engine RPM, steam or sweet-smelling vapor from under the hood, visible coolant puddle under the front of the vehicle, and coolant staining or white/green residue around the pump body. In severe cases, a failed pump allows the impeller to spin freely on the shaft, meaning no coolant circulation even though the pump appears to be turning.

How much does water pump replacement cost?

Water pump replacement costs depend heavily on the pump location. For serpentine belt-driven water pumps (external), expect $200-$500 total including parts ($50-$250) and labor (1-2 hours). For timing belt-driven water pumps (internal), costs range from $500-$1,200+ because the timing belt, tensioner, and idler pulleys should be replaced simultaneously, and labor is 3-6 hours. Luxury and European vehicles often cost $800-$1,500+ due to complex engine layouts. DIY replacement of a serpentine belt-driven pump is feasible at $50-$250 in parts. Always budget for new coolant ($15-$30) and a thermostat ($15-$40) as well.

Should I replace the timing belt when replacing the water pump?

Yes, absolutely. If your water pump is driven by the timing belt, you should replace the timing belt, tensioner, and idler pulleys at the same time. The vast majority of the labor cost is accessing these components — the timing cover, belt, and tensioner must already be removed to reach the water pump. Replacing just the pump and reusing an old timing belt means you risk the belt failing shortly after and paying the full labor cost again. Conversely, if your timing belt is due for replacement, always include the water pump. This combined service is called a timing belt kit and represents the best value for long-term reliability.

Should I flush the coolant when replacing the water pump?

Yes, you should always flush the cooling system when replacing the water pump. The system must be drained to remove the old pump, so this is the ideal time for a complete flush. Old coolant contains contaminants, scale, and degraded additives that can damage the new pump seal and impeller. Flush the system with clean water until it runs clear, then refill with the correct type and ratio of coolant for your vehicle (check your owner's manual — using the wrong coolant type can cause corrosion and gasket damage). Bleed all air from the system following the manufacturer's procedure to prevent air pockets that cause hot spots and overheating.

What is the weep hole on a water pump?

The weep hole is a small drain hole located on the bottom of the water pump housing between the shaft seal and the bearing. It is an intentional design feature that serves as an early warning system for seal failure. When the internal shaft seal begins to wear, a small amount of coolant seeps past the seal and drains through the weep hole rather than contaminating the bearing. A dry weep hole indicates a healthy seal. Minor occasional dripping is normal, but a steady drip or stream of coolant from the weep hole means the seal has failed and the pump needs replacement. Do not plug the weep hole — it protects the bearing from coolant contamination.

How long does a water pump last?

Water pumps typically last 60,000-100,000 miles, though some last significantly longer. Timing belt-driven pumps are usually replaced at the timing belt service interval (60,000-105,000 miles depending on the vehicle) as a preventive measure. Serpentine belt-driven pumps may last 100,000-150,000+ miles but should be inspected regularly for leaks and noise. Factors affecting lifespan include coolant maintenance (old, acidic coolant corrodes the impeller and seal), belt tension (excessive tension accelerates bearing wear), coolant type (using incorrect coolant causes seal deterioration), and operating conditions (frequent overheating shortens pump life).

What is an interference engine, and why does it matter for water pump failure?

An interference engine is one where the pistons and valves occupy the same space in the cylinder at different times during the engine cycle. If the timing belt or chain breaks or skips teeth (which can happen if a timing belt-driven water pump seizes), the pistons collide with the open valves, bending the valves and potentially damaging the pistons, cylinder head, and other internal components. This turns a $500-$1,000 water pump and timing belt job into a $3,000-$8,000 engine repair or replacement. Most modern engines are interference designs, which is why replacing the water pump preventively with the timing belt is critical.

What type of coolant should I use when replacing the water pump?

Always use the coolant type specified by your vehicle manufacturer — using the wrong type can cause corrosion, gasket damage, and premature pump failure. Common types include: green IAT (Inorganic Acid Technology) coolant for older vehicles, orange/red OAT (Organic Acid Technology) for many GM, VW, and Asian vehicles, yellow/purple HOAT (Hybrid OAT) for Ford and Chrysler, and blue/pink for specific Asian manufacturers. Never mix coolant types as they can gel and clog the cooling system. Use a 50/50 mix of coolant and distilled water (not tap water, which contains minerals that cause scale). Pre-mixed coolant is convenient and ensures the correct ratio.

Car Parts Finder USAUsed 2013 Aston-Martin Vantage Water Pump

Quality used parts from verified sellers. Find quality 2013 Aston-Martin Vantage water pump parts.

Find quality Aston-Martin water pump at the best prices

Save 50-70% compared to dealership prices

OEM and aftermarket options available

Guaranteed fitment with buyer protection

1M+ Parts

Nationwide Search

Buyer Protected

SSL Secured · Your privacy matters · Read our privacy policy

Searching for 2013 Aston-Martin Vantage Water Pump Listings

We're actively sourcing water pump listings for the 2013 Aston-Martin Vantage. Search now to see the latest available parts from our seller network.

Search Latest Water Pump Listings

Browse 2013 Aston-Martin Vantage Parts by Make

Select a vehicle manufacturer to find compatible parts

Search. Compare.
Get Your Part.

Find the right part in 4 simple steps

Search

Enter your year, make, model, and the part you need.

Compare

Browse results from thousands of sellers. Compare prices and conditions.

Connect

Click to view the listing or contact the seller directly.

Buy

Purchase from the seller with confidence. Save 50-70% on parts.

About

Car Parts Finder USA

Need a Water Pump for your 2013 Aston-Martin Vantage? Car Parts Finder USA searches thousands of sellers to find the best water pump at the lowest prices with guaranteed fitment.

Water Pump from verified sellers with condition grading
Compare prices across multiple sources instantly
Warranty included from most sellers (30-90 days)
Free searches with no account required

Learn More About Us

Car Parts Finder USA — Find quality auto parts fast

AI Search Engine

Compare Parts

Free Delivery

Fast Search

Common Replacement Age — Buying Tips

At 13 years old, your 2013 Aston-Martin Vantage is at the age where water pump replacement becomes common. Aftermarket and quality used parts offer excellent value — often 50-70% less than OEM with comparable reliability.

Price Range:

Used

$30-$100

Aftermarket

$50-$250

OEM

$100-$500

Free Search • No signup required • Instant access

Why Choose Used Car Parts?

Quality used parts from verified sellers

Verified seller network

Quality guaranteed

Competitive pricing

Return policy available

Fast shipping

Shop 2013 Aston-Martin Vantage Parts by Category

Find quality 2013 Aston-Martin Vantage parts across all major categories from verified sellers nationwide.

Engine & Transmission

Complete engines, transmissions, alternators, starters, radiators, and all powertrain components.

Browse Engine & Transmission

Body Parts & Glass

Doors, hoods, fenders, bumpers, windshields, headlights, taillights, and exterior components.

Browse Body Parts & Glass

Interior & Electronics

Seats, dashboards, airbags, stereos, navigation systems, ECUs, and electronic modules.

Browse Interior & Electronics

Suspension & Brakes

Struts, shocks, control arms, brake calipers, rotors, pads, and complete brake systems.

Browse Suspension & Brakes

About the 2013 Aston-Martin Vantage Water Pump

The water pump is the heart of your vehicle's cooling system, circulating coolant through the engine block, cylinder head, heater core, and radiator to maintain optimal operating temperature. It is a centrifugal pump driven by the serpentine belt, timing belt, or timing chain. When the water pump fails, the engine can overheat rapidly, potentially causing catastrophic damage including blown head gaskets, warped cylinder heads, or complete engine failure.

Signs of Failure

Coolant leak from the front-center of the engine (weep hole drip)
Engine overheating or running hotter than normal
Squeaking, squealing, or grinding noise from the water pump area
Steam rising from under the hood
Sweet coolant smell inside or outside the vehicle
Coolant puddle under the vehicle near the front of the engine
Temperature gauge fluctuating or reading high
Visible corrosion or coolant staining around the water pump

Replacement Info

Water pump replacement difficulty depends primarily on whether the pump is driven by the serpentine belt (external, easier access) or the timing belt/chain (internal, requires significant disassembly). For serpentine belt-driven pumps, the process involves draining the coolant, removing the belt, unbolting the pump, cleaning the mating surface, and installing the new pump with a new gasket or sealant. For timing belt-driven pumps, the timing cover, timing belt, and tensioner must be removed first — it is strongly recommended to replace the timing belt, tensioner, and idler pulleys at the same time since the labor overlaps. Always flush the cooling system and use the correct coolant type when replacing the water pump.

Time: 2-4 hours (up to 6 hours if timing belt driven)

Difficulty: Moderate to Difficult

2013 Aston-Martin Vantage Water Pump — Price Comparison

Used / Salvage

$30-$100

Best value option. Tested parts from salvage vehicles.

Aftermarket

$50-$250

New parts from third-party manufacturers. Great quality at lower cost.

OEM / Dealer

$100-$500

Original factory parts. Guaranteed fitment and manufacturer warranty.

Where to Find 2013 Aston-Martin Vantage Water Pump

Online Sellers

Search hundreds of online parts sellers. Compare prices instantly.

Search Online

Local Scrapyards

Find local scrapyards with your part in stock. Call for availability.

Search Parts

DIY Junkyards

Pull your own parts and save even more. U-pull-it yards nationwide.

Browse Junkyards

Select Your Model Year

Aston-Martin Vantage Water Pump — All Years

Browse water pump for every Aston-Martin Vantage model year

2022 2021 2019 2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006

Showing most recent years. Parts available for 2006-2022.

Other Aston-Martin Models — Water Pump

Find water pump for other Aston-Martin vehicles

Aston-Martin Db11

2017-2022

Water Pump

Aston-Martin Db9

2005-2015

Water Pump

Aston-Martin Db9-Gt

2016-2016

Water Pump

Aston-Martin Dbs

2008-2022

Water Pump

Aston-Martin Dbs-Superleggera

2019-2021

Water Pump

Aston-Martin Dbx

2021-2025

Water Pump

Aston-Martin Rapide

2010-2012

Water Pump

Aston-Martin Rapide-S

2014-2017

Water Pump

Aston-Martin Vanquish

2014-2017

Water Pump

Aston-Martin Vanquish-S

2005-2018

Water Pump

Used Car 2013 Vantage Water PumpFrequently Asked Questions

1How much does a used car 2013 Aston-Martin Vantage water pump cost?

2Are used car 2013 Vantage water pump parts reliable?

3Where can I buy used car 2013 Aston-Martin Vantage water pump?

4What are signs I need to replace my 2013 Vantage water pump?

5Do used 2013 Vantage water pump parts come with warranty?

Related 2013 Vantage Parts

Engine Transmission Engine Computer Alternator Radiator Fender Hood A/C Compressor

Don't see your part? Use the search above to find all 683+ parts

More 2013 Vantage Water Pump Options

Junkyard Parts

DIY Savings - Pull your own parts for maximum savings

Browse Junkyard

Salvage Parts

Inspected Quality - Professionally inspected parts from salvage vehicles

Browse Salvage

Recycled Parts

Eco-Friendly - Sustainable auto parts that help the environment

Browse Recycled

Features

Your 2013 Vantage Water Pump

Compare prices from multiple sellers and find the best deal.

OEM vs Aftermarket — 2013 Aston-Martin Vantage Water Pump

Recommendation: OEM or Quality Aftermarket

Water pump quality directly affects engine longevity — a failed pump can destroy an engine in minutes from overheating. For timing belt-driven pumps, OEM is strongly recommended since you are already investing significant labor to access the pump and a failure means repeating all that work. Quality aftermarket pumps from brands like Gates, GMB, Aisin, and Continental are reliable options for serpentine belt-driven applications where access is easier. Avoid the cheapest options, which may use inferior bearing seals and plastic impellers that can crack or deteriorate in hot coolant.

OEM Advantages

Metal impeller guaranteed (some aftermarket use plastic)
Premium bearing and seal quality for long life
Exact fit with correct gasket surface finish
Known compatibility with OE coolant types
Essential for timing belt-driven applications

Aftermarket Advantages

Significant cost savings (40-60% less)
Quality brands use metal impellers and sealed bearings
Often includes new gasket and hardware

Used 2013 Aston-Martin Vantage Water Pump | Quality Pre-Owned Parts

Car Parts Finder USAUsed 2013 Aston-Martin Vantage Water Pump

Vehicle Details

Searching for 2013 Aston-Martin Vantage Water Pump Listings

Browse 2013 Aston-Martin Vantage Parts by Make

Search. Compare.Get Your Part.

Search

Compare

Connect

Buy

About

Common Replacement Age — Buying Tips

Why Choose Used Car Parts?

Shop 2013 Aston-Martin Vantage Parts by Category

Engine & Transmission

Body Parts & Glass

Interior & Electronics

Suspension & Brakes

About the 2013 Aston-Martin Vantage Water Pump

Signs of Failure

Replacement Info

2013 Aston-Martin Vantage Water Pump — Price Comparison

Used / Salvage

Aftermarket

OEM / Dealer

Where to Find 2013 Aston-Martin Vantage Water Pump

Online Sellers

Local Scrapyards

DIY Junkyards

Aston-Martin Vantage Water Pump — All Years

Other Aston-Martin Models — Water Pump

Aston-Martin Db11

Aston-Martin Db9

Aston-Martin Db9-Gt

Aston-Martin Dbs

Aston-Martin Dbs-Superleggera

Aston-Martin Dbx

Aston-Martin Rapide

Aston-Martin Rapide-S

Aston-Martin Vanquish

Aston-Martin Vanquish-S

Used Car 2013 Vantage Water PumpFrequently Asked Questions

Related 2013 Vantage Parts

More 2013 Vantage Water Pump Options

Junkyard Parts

Salvage Parts

Recycled Parts

Your 2013 Vantage Water Pump

OEM vs Aftermarket — 2013 Aston-Martin Vantage Water Pump

OEM Advantages

Aftermarket Advantages

Related Parts for 2013 Aston-Martin Vantage

What to Look for When Buying a 2013 Aston-Martin Vantage Water Pump

Frequently Asked Questions — 2013 Aston-Martin Vantage Water Pump

Search. Compare.
Get Your Part.